MDC (Materials Development Corp.) DUO CHUCK 8512-6 Dual Integrated Hot Chuck CV measurement system in a dark box for Sale

Deinstalled, barrier bagged, warehoused
Location: Avezzano (AQ) 67051 Italy.
See attached photos showing the equipment.

Parts included:-
1. MDC Model 8512-6 Dual Integrated Hot Chuck CV measurement system in dark box.
2. MDC Model 8604 DuoChuck Microscope Stand.
3. MDC CSM/Win (Not included - available at extra cost).

The Materials Development Corporation DuoChuck Integrated Hot Chuck System combines two microprocessor-based hot chuck controllers, two hot chucks, a multiplexer, and dual programmable stress supplies into one sturdy, solid aluminum dark box. All system operations are controlled by a standard RS-232C serial port.In one dark box enclosure, the MDC DuoChuck combines two independent hot chucks, all temperature controller and stress supply electronics and a multiplexer. The multiplexer can select one of five probes from either chuck for C-V measurement. This space-saving package can be controlled by the MDC CSM/Win SYSTEM (Not included - available at extra cost) to make MOS mobile ion measurements almost five times faster than a conventional hot chuck system. This speed is made possible by efficient computer control of the probe selection and hot chuck cycling. While the wafer on one hot chuck is in the heating cycle, C-V measurements are taken on the wafer on the other hot chuck. All test parameters - voltage sweep limits, soak time, soak temperature, soak bias, and oxide thickness are selectable via user-friendly display screens. Sophisticated control and measurement software performs the entire test without operator intervention. An advanced test algorithm checks for measurement anomalies and corrects them or deletes further measurements on the affected probe. Time is not wasted on invalid measurements. A comprehensive test summary lists all test results and statistics. Test data such as flatband voltage shifts, Qss, and substrate doping may be stored on disk for later analysis with a spreadsheet program. C-V plots may be displayed on the computer screen and plotted or printed.For critical probing applications, use the Model 8604 DuoChuck Microscope Stand (Included). This accessory supports a microscope on linear bearings which allows the operator to view a wafer on either chuck. The MDC CSM/Win System with the new DuoChuck Integrated Hot Chuck System assures the most consistent and rapid C-V measurements from shift to shift and operator to operator.  
General Specifications and Requirements
POWER: 108 to 125 VAC, 20 Amps, 50 to 60 Hz 208 to 230 VAC option available.
COOLANT SUPPLY: Tap water at 2 gallons/minute (8 liters/minute) at 15 psi, Maximum pressure of 20 psi (1.3 Bar). No de-ionized water.
VACUUM SUPPLY: 20-25 inches (500-600 mm) Hg.
LIGHTS FOR C -V STABILIZATION: 2, computer controlled
BIAS VOLTAGE SUPPLY: 2, ±20 V range, 0.1 V resolution
DIMENSIONS: Width 25.5" (65 cm); Depth 20.5" (64 cm); Height 9; (23 cm)  
Temperature Specifications
RANGE: Cooling water ambient to 300° C.
DISPLAY ACCURACY: ±1°C (15°C to 300°C)
OVER-TEMPERATURE: Factory set shutdown above 315°C
THERMOCOUPLE: Type J (2 required for each chuck)  
Communications FORMAT RS-232C, 8-bit character, 1 stop bit, no parity
BAUD RATES: 300, 600, 1200, 2400, 4800, 9600.  
MODEL 8512-6  CHUCK DIAMETER 6.6" (165 mm) HEATING TIME 320 seconds (ambient to 300°C) Cooling Time (300°C to 50°C) 225 seconds

I have taken 2 videos of the hot-chuck system and uploaded them to youtube.
They are visible at the following links:-

https://youtu.be/PZF8LhTNEWo

https://youtu.be/IMMMXKapYmY

If you can't access youtube, let me know and I'll send you the videos via another file-sharing method.